3D & CNC PRINTER PARTS
Showing all 11 results
- 3D & CNC PRINTER PARTS
775 Motor Bracket Heavy Duty Plastic With Support Screws Motor Fixed Base L Shaped Plastic Body For DIY Mounting Bracket in Pakistan
-32%3D & CNC PRINTER PARTS775 Motor Bracket Heavy Duty Plastic With Support Screws Motor Fixed Base L Shaped Plastic Body For DIY Mounting Bracket in Pakistan
- Any Color could be available.
- Usage: Fit to 775 DC motor as a shelf or holder.
- Motor mounting hole: 4 mm (suitable for M4 screw)
- Surface: Plastic
- Materials: High Strength Plastic
SKU: BRACKET 775 MOTOR - 3D & CNC PRINTER PARTS
CNC Shield V3 Engraving Machine Module/ A4988 Driver Expansion Board for Arduino in Pakistan
-36%3D & CNC PRINTER PARTSCNC Shield V3 Engraving Machine Module/ A4988 Driver Expansion Board for Arduino in Pakistan
- Using A4988 module
- Five different step mode
- Adjust the maximum current output, so as to obtain a higher rate of step.
- Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals
- Can drive four A4988 stepper motor
SKU: CNC SHIELD V3 - 3D & CNC PRINTER PARTS
CNC Shield V4 Engraving machine module/ A4988 Driver Expansion Board for Arduino in Pakistan
-31%3D & CNC PRINTER PARTSCNC Shield V4 Engraving machine module/ A4988 Driver Expansion Board for Arduino in Pakistan
- 3 axis stepper motor driver
- Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine,.
- 2A can be controlled within the two-phase four-wire stepper motor.
- Released the digital IO interface, easy to connect to other modules, such as END STOP.
- Released the I2C interface, you can connect to the LCD I2C or other I2C module.
- Power DC5V interface, 7.5-12V voltage input.
- GRBL compatible
- Worked with arduino nano.
SKU: CNC SHIELD V4 - 3D & CNC PRINTER PARTS
Horizontal KFL08 8mm Bearing Bracket For Trapezoidal T8 Lead Screw 3D Printers CNC Parts in Pakistan
-51%3D & CNC PRINTER PARTSHorizontal KFL08 8mm Bearing Bracket For Trapezoidal T8 Lead Screw 3D Printers CNC Parts in Pakistan
- Model: KFL08
- Bore:8mm/0.31″
- Outer diameter: approx. 26mm/1.02″
- Hole diameter: approx. 5mm/0.20″
- Hole Centers Spacing: approx. 37mm/1.46″
- Length: approx. 47mm/1.85″
- Height: approx. 11mm/0.43″
- Material: Zinc Alloy
SKU: KFL08 BEARING 8MM - 3D & CNC PRINTER PARTS
Nema17 Stepper Motor 4 Wire 42 D Shaft Motor 42BYGH 1.7A (17HS4401) 3D Printer Motor CNC XYZ in Pakistan
-48%3D & CNC PRINTER PARTSNema17 Stepper Motor 4 Wire 42 D Shaft Motor 42BYGH 1.7A (17HS4401) 3D Printer Motor CNC XYZ in Pakistan
- General Specification:
- Step angle accuracy: + – 5%(full step,not load)
- Resistance accuracy: + – 10%
- Inductance accuracy: + – 20%
- Temperature rise: 80deg Max(rated current,2 phase on)
- Ambient temperature ———-—20deg ~+50deg
- Insulation resistance:100MΩ Min,500VDC
- Insultion Strength——–500VAC for one minute
SKU: NEMA 17 MOTOR - 3D & CNC PRINTER PARTS
Stepper Motor Driver A4988 3D Printer Step Stick Carrier Reprap 4-layer PCB RAMPS in Pakistan
-44%3D & CNC PRINTER PARTSStepper Motor Driver A4988 3D Printer Step Stick Carrier Reprap 4-layer PCB RAMPS in Pakistan
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Can interface directly with 3.3 V and 5 V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solder able ground pad below the driver IC on the bottom of the PCB
- Module size, pin out, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45 V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
SKU: A4988 MOTOR DRIVER